The gateway to Europe's
integrated metrology community.

The list shows all projects coordinated within the Technical Committee for Length.

Projects TC-L

Subject
Reg. No.
Starting
TITLE
Coordinating Institute
Status
Collaboration Type
KCDB
L 1138 2009-11-23 Key comparison of gauge blocks by interferometry DZM completed Comparison EURAMET.L-K1.2
L 1124 2007-02-01 Comparison of Type F2 Software Measurement Standards for Surface Texture NPL completed Research
L 1105 2009-06-29 Bilateral comparison on micro-CMM artefacts METAS completed Research
L 1088 2008-10-01 Towards truly 3D metrology for advanced micro-parts VSL completed Research
L 1087 2008-09-29 Average diameter of polymer particles with spherical form JV completed Research
L 1074 2008-10-15 Angle key comparison using an autocollimator PTB completed Comparison EURAMET.L-K3.2009
L 1068 2008-11-01 TC-L initiative to archive data of Key and Supplementary comparisons BEV completed Research
L 1063 2008-08-18 EURAMET link to the CCL key comparison CCL-K11 MIKES completed Traceabillity
L 1057 2008-06-01 Calibration of XXX Pin Gauges by Mechanical Probing NSAI NML completed Comparison
L 1053 2008-07-28 Supplementary Comparison: Involute Gear Artifacts PTB completed Comparison EURAMET.L-S24
L 1045 2008-12-01 Direct comparison of 3 optical femtosecond comb generators BEV completed Comparison
L 1016 2008-01-02 Interferometric measurements of gauge blocks DZM completed Consultation
L 1012 2008-02-01 Limitations of measuring methods for the depth of the groove DZM completed Research
L 1005 2007-06-14 Dimensional measurements - Using AFM and profilometers in Surface Measurement DFM completed Consultation
L 1003 2007-11-09 Key Comparison: Intercomparison of Measurements on Surface Texture Standards LNE completed Comparison EURAMET.L-K8
L 925 2006-08-01 Supplementary Comparison: Intercomparison of Measurements on Step Height Standards by SPM PTB completed Comparison EUROMET.L-S15.a
L 914 2006-09-01 Introduction of primary standard of length into a national metrology laboratory MIRS/UM-FS/LTM completed Consultation
L 910 2006-07-07 Bilateral supplementary comparison of squareness measurements SMU completed Comparison EUROMET.L-S19
L 905 2006-08-01 Bilateral supplementary comparison of squareness measurements SMU completed Comparison EUROMET.L-S18
L 882 2006-02-01 Key Comparison: Calibration of line scales EUROMET.L-K7 MIRS/UM-FS/LTM completed Comparison EUROMET.L-K7.2006
L 875 2005-11-01 Bilateral supplementary comparison of a tape measure METAS completed Comparison EUROMET.L-S17
L 873 2006-01-01 Absolute frequency measurements of stabilized lasers (MeP) in northern Europe for BIPM.L-K11 MIKES completed Comparison
L 871 2005-09-01 Training and practical issues in angle metrology INRiM completed Consultation
L 870 2007-11-01 Bilateral key comparison of measurements on precision polygons INRiM completed Comparison EUROMET.L-K3.1
L 868 2004-01-01 Tip sample interactions in scanning probe microscopy NPL completed Research
L 866 2006-01-01 Interferometric calibration of microdisplacement actuators INRiM completed Research
L 812 2005-01-01 Key Comparison: Calibration of Diameter Standards INRiM completed Comparison EUROMET.L-K4.2005
L 807 2005-04-04 Workshop on Micro Coordinate Measuring Machines (µCMM) METAS completed Research
L 801 2004-01-01 Calibration of stabilised laser sources by the optical femtosecond comb generator of BEV BEV completed Traceabillity
L 797 2003-06-01 Supplementary Comparison: Calibration of gauge blocks by mechanical comparison NPL completed Comparison EUROMET.L-S16
L 795 2004-11-01 Bilateral comparison on laser frequency calibration BEV concluded Research
L 794 2004-08-30 Training and practical issues in gauge block metrology BEV completed Consultation
L 789 2004-06-28 Using stabilized lasers for Kösters type gauge block interferometers. BEV completed Consultation
L 777 2004-05-17 Key Comparison: Step gauge calibration CEM completed Comparison EUROMET.L-K5.2004
L 767 Exchange of experience in length calibration and proficiency testing DFM completed Research
L 765 2004-03-01 Calibration of 9 steel gauge blocks by mechanical comparison MCCAA-SMI completed Comparison
L 744 2003-11-01 Studies on the acoustic method for determination of the effective air temperature and refractive index of air MIKES completed Research
L 743 2004-05-15 EURAMET key comparison, CMM 2-D Artifact: Ball Plate PTB completed Comparison EUROMET.L-K6
L 728 2003-05-01 Bilateral comparison of a 420mm x 420mm CMM ball plate. NSAI NML completed Research
L 727 2003-07-01 Calibration of 8 Gauge Blocks by Interferometry NSAI NML completed Research
L 725 2003-03-12 Comparison of indexing tables, with small angle devider SMD completed Comparison
L 718 2003-05-19 Training in laser frequencyy metrology BEV completed Consultation
L 707 2003-07-01 Intercomparison of Measurement on Step Height Standards by SPM PTB completed Comparison
L 679 2002-06-01 Calibration of ring and plug gauges VSL completed Research
L 677 2003-01-01 Supplementary comparison of steel tape measures METAS completed Comparison EUROMET.L-S14
L 672 2002-09-01 Determination of form/topography of high-quality flats PTB completed Research
L 659 2001-11-01 The combination of scanning probe microscopy, optical interferometry and x-ray interferometry NPL completed Research
L 654 2002-05-01 Exchange of experience in gauge blocks and material measures of length measurements GUM completed Consultation
L 652 2002-03-01 Calibration of short steel gauge blocks by mechanical comparison MIRS/UM-FS/LTM completed Research
L 649 2002-05-01 Sensitivity Transfer Standards for Form Measuring Instruments PTB completed Research
158 result(s)